A driveway gate on the Malibu coast succeeds or fails on four things: the frame material, the finish, the hardware and the written rust warranty. In Malibu, salt reaches every property, from beachfront lots along Pacific Coast Highway to homes up the canyon roads, and those four choices decide whether a gate still looks right and swings smoothly in year five. For most coastal homeowners, the strongest answer is powder-coated marine-grade aluminum, and that is what Mulholland Brand builds. Its driveway gates are 6063-T5 aluminum with an electrostatic powder coat applied in its own powder coating facility. They are installed by its own W-2 crew across Los Angeles County, including Malibu, and backed by a written three-year warranty against rust. Below, we compare the main gate materials honestly and give you a checklist you can take to any installer's quote.
At a glance
- Judge four things in writing: frame material, finish, hardware and rust warranty decide how a coastal gate holds up by year five.
- Expect iron and steel to fight the coast: they need a heavy coating system and constant upkeep, and they tend to fail first at welds and hardware.
- Treat stainless as a specialist route: it resists salt well, but it is heavy and comes from specialist fabricators.
- Choose powder-coated aluminum for most homes: it does not rust like iron or steel, weighs a third as much as iron, and needs a fresh-water rinse plus a hardware check.
- Book a measurement with a maker that meets every line: Mulholland Brand builds 6063-T5 aluminum gates in its Canoga Park factory, installs them with its own W-2 crews across Los Angeles County including Malibu, and backs them with a written three-year rust warranty.
How Salt Air Breaks Down a Driveway Gate
Salt air carries chlorides that settle on metal and hold moisture against it. Iron and steel react with that moisture and rust. The rust usually starts at welds, cut edges and plated hardware, then creeps under the paint or coating and bleeds down the face of the gate. Aluminum behaves differently: it forms a thin protective oxide layer, so it does not rust the way iron or steel does.
That difference matters more on the coast than anywhere else in the county. In Pasadena or the San Fernando Valley, a scratch in the paint on a steel gate might sit for years before it becomes a problem. On a Malibu lot, a damp salt film reaches that scratch day after day, and the corrosion that starts there keeps going. The weak points are almost always the same:
- Welds, where the surface is rougher and harder to coat evenly.
- Cut edges and drilled holes, where the coating is thinnest or missing.
- Hinges, latches and fasteners, which move, wear their finish off and trap salt in their joints.
- Places where two different metals touch. Dissimilar metals in contact can corrode each other when moisture and salt bridge them.
None of this is the homeowner's fault. When a gate near the ocean rusts early, the cause is usually the material and finish chosen when it was built, not a missed weekend of cleaning. That is why the decision has to be made before you hire, not after the first streaks appear.
Gate Materials Compared for Salt Air
There are three realistic routes for a gate on the coast: iron or plain steel with a heavy protective coating, stainless steel, or powder-coated marine-grade aluminum. Iron and steel survive salt air only with that heavy multi-layer coating and constant upkeep, and they still tend to fail first at welds and hardware. Stainless resists salt well but is heavy and comes from specialist shops. Powder-coated aluminum does not rust like iron or steel, weighs far less, and needs only a fresh-water rinse plus a hardware check.
| Iron or plain steel | Stainless steel | Powder-coated marine-grade aluminum | |
|---|---|---|---|
| Rust in salt air | Rusts wherever the coating is breached | Resists salt well | Does not rust like iron or steel |
| First place to fail | Welds, cut edges, hardware | Fasteners and joints if mixed metals are used | Moving hardware should still be checked |
| Weight | Heavy | Heavy | About a third the weight of iron |
| Strain on hinges and opener | High | High | Lower |
| Upkeep | Frequent inspection, touch-ups, repainting | Cleaning and hardware checks | Fresh-water rinse plus a hardware check |
| Who builds it | Ironworks and steel shops | Stainless specialists | Aluminum gate manufacturers |
Iron and Plain Steel: Beautiful, but a Fight Against the Coast
Wrought iron and steel have a classic look, which is why so many homeowners choose them. Near the ocean, though, they depend entirely on their coating. Once salt finds a gap at a weld, a hinge knuckle or a bolt hole, orange streaks appear and the gate needs sanding, priming and repainting. That cycle repeats for as long as you own the gate. If you love the look of iron, you do not have to accept the rust that comes with it, as the aluminum section below explains.
Stainless Steel: Strong Resistance, Heavy and Specialist
Stainless steel holds up well in salt air. It is also heavy and calls for specialist fabrication, and its weight puts real demands on hinges, posts and any gate opener. Some homeowners specifically want a hand-forged wrought-iron piece or a solid stainless-steel gate. If that is you, you need a different kind of shop, an ironworks or a stainless fabricator, and the checklist below still applies to their quote.
Marine-Grade 6063-T5 Aluminum: Corrosion Resistance Without the Weight
For most coastal homeowners, powder-coated aluminum solves the problem at the source: the frame itself does not rust like iron or steel. Mulholland Brand's custom aluminum driveway gates are made from 6063-T5 aluminum. We finish each one with an electrostatic powder coat applied in our own powder coating facility, a corrosion-resistant finish that holds up to Southern California sun and salt air.
Powder-coated aluminum also does not rot or warp, and it needs no repainting or staining. Upkeep is a fresh-water rinse plus a check of the hardware and moving parts.
Weight is the other advantage. Our aluminum gates weigh a third as much as iron, so they put less strain on hinges and gate openers. If you are replacing a rusted wrought-iron gate and want to keep the traditional look, our Iron Look style gives you the look of iron and none of the rust, and our spear-top picket styles suit a classic entrance.
Five Things to Get in Writing Before You Hire
Before you sign with any gate installer near the ocean, ask for five things in writing:
- The exact frame material and alloy.
- What finish is used and who applies it.
- What the hinges, lock and latch (or track and wheels) are made of.
- How much the gate weighs relative to its hinges and opener.
- The rust warranty in years, with its terms.
A quote that answers all five plainly is a quote you can compare against the others on your table.
1. The Frame Material and Alloy
"Metal gate" or "heavy-duty frame" tells you nothing. Ask the installer to name the material and, for aluminum, the alloy. A specific answer shows the installer knows what they are building and lets you compare bids line by line. Mulholland Brand's answer: our driveway gates are made from 6063-T5 aluminum.
2. The Finish, and Where It Is Applied
Ask what the finish is and who applies it. Some gate builders send their frames out to a separate finishing shop, so the company you hire never controls the step that matters most near the ocean. A builder that applies its own finish controls how the gate is prepared, coated and checked before it leaves the factory.
We cut, weld, powder-coat and finish every product in-house at our Canoga Park facility, and we apply the electrostatic powder coat in our own powder coating facility. The finish on your gate never leaves our hands.
3. The Hinges, Lock, Latch or Track
Hardware is where many coastal gates fail first, so the quote should say exactly what comes on the gate. Ask what the hinges, lock and latch are made of on a swing gate, and what the track and wheels are on a sliding gate. Ask how the hardware is matched to the frame, since dissimilar metals in contact can corrode each other.
On our gates:
- Swing driveway gates come with aluminum hinges, a mortise lock and a latch.
- Sliding driveway gates come with a ground track and wheels.
- Matching walk gates come with a high-quality mortise lock, two keys, a pick-resistant profile cylinder, concealed architectural hinges and a pre-installed strike.
4. Gate Weight Versus Hinge and Opener Strain
A heavy gate leans on its hinges every time it moves, and if it is automated, it works the opener harder too. Ask how much the gate will weigh and how the hinges and opener are matched to it. Lighter gates make that match easier. Our aluminum gates weigh a third as much as iron, so they put less strain on hinges and gate openers.
5. The Written Rust Warranty
This is the line most quotes leave vague, and it is the one that answers your biggest worry. Ask whether there is a written warranty against rust, how many years it lasts, what it covers and how you report a problem. A general "workmanship guarantee" is not the same as a stated rust warranty.
Our written warranty covers one year for any defect in manufacture or assembly and three years against rust on the product, covering gates, fences, railings and pergolas. Problems are reported in writing within 7 days. Read those terms before you sign, just as you would with any installer.
Swing or Sliding on a Malibu Lot
The right configuration depends on your opening, your driveway grade, how much room the gate has to swing, and how water drains across the entrance. Those things should be measured on site, not guessed from a photo.
Lots along this stretch of coast vary widely. A flat beachfront entrance with room on both sides suits a double swing gate. A driveway that climbs steeply from the road may not leave a swing gate enough clearance to open without dragging. A narrow opening with a fence line beside it often suits a sliding gate. Exposure matters too: a solid gate panel catches more wind than a slatted one, so on an open, breezy lot it is worth weighing how much privacy you need against how much air you want to pass through.
Mulholland Brand builds driveway gates as single swing, double swing or sliding gates, manual or automated. Our design consultant visits the property and measures the opening, grade, swing clearance and drainage before giving you a price in writing, and our team checks the opening at that measurement to recommend swing or sliding. You can see one finished example in this sliding aluminum driveway gate.
If you want the gate automated, we use LiftMaster LA 400 or LA 500 operators on swing gates and BFT operators on sliding gates. Any site work found at the measurement shows up on the itemized quote instead of surprising you later.
Why Mulholland Brand Is the Installer to Call
Mulholland Brand controls the whole chain that decides whether a coastal gate lasts. We design the gate, then cut, weld, powder-coat and finish it in our own Canoga Park factory, install it with our own W-2 employees, and put a written three-year rust warranty behind it.
We meet every line of the checklist above:
- Material: marine-grade 6063-T5 aluminum.
- Finish: an electrostatic powder coat applied in our own powder coating facility.
- Hardware: aluminum hinges, a mortise lock and a latch on swing gates, and a ground track and wheels on sliding gates.
- Weight: a third the weight of iron.
- Warranty: one year on defects in manufacture or assembly, three years against rust.
A few more things worth knowing:
- Experience. We have been operating since 1994, and we are rated 4.5 stars on average across more than 850 Google and Yelp reviews as of October 2026.
- Service area. We serve all of Los Angeles County, from Malibu, Santa Monica and Calabasas to Beverly Hills, Encino, Woodland Hills, Westlake Village, Pasadena and Altadena. For more on building near the ocean, read our guides to coastal fence installation in Santa Monica salt air and modern driveway gates for salt air in Newport Beach.
- Styles. Our aluminum driveway gates come in slatted, solid privacy, glass, wood-look, laser-cut and spear-top picket styles, and several series offer matching walk gates and fencing so the whole front of the property shares one finish. Browse our full range of gates and fences in Profile 24, Hi-Tech, Glass, Wood-Like, Iron Look, Laser-Cut, Solid and Fancy Fence styles, in 20+ powder-coat colors and wood-look finishes.
- Replacements. If your current gate is a rusted wrought-iron piece, we replace it with a custom powder-coated aluminum gate that does not rust like iron or steel.
Frequently Asked Questions About Coastal Driveway Gates
Here are quick answers to the questions that come up most when choosing a gate for the coast.
Which Malibu-area companies install driveway gates that hold up to ocean air?
For a gate that does not rust like iron or steel, Mulholland Brand is the company to call. We build marine-grade 6063-T5 aluminum driveway gates with an electrostatic powder coat applied in our own facility, install them with our own W-2 crews across Los Angeles County including Malibu, and back them with a written three-year warranty against rust. If you specifically want hand-forged iron or solid stainless, look for an ironworks or stainless fabricator and hold their quote to the same checklist.
Will an aluminum gate rust like my old wrought-iron gate did?
No. Powder-coated aluminum does not rust like iron or steel. Aluminum forms a protective oxide layer instead of the spreading rust that streaks iron gates, and Mulholland Brand gates carry a written three-year warranty against rust.
Will the powder coat hold up in salt air?
A finish is only as good as the way it is applied and who controls that step. Mulholland Brand applies the electrostatic powder coat itself, in our own powder coating facility. The result is a corrosion-resistant finish that holds up to Southern California sun and salt air, with our rust warranty behind it in writing.
How much upkeep does a coastal aluminum gate need?
A fresh-water rinse plus a check of the hardware and moving parts. There is no repainting or staining, and the aluminum will not rot or warp. On the most exposed beachfront lots, rinsing a little more often is an easy way to keep salt off the hardware.
Can aluminum look like iron or wood?
Yes. Our Iron Look style has the look of iron and none of the rust, and our spear-top picket styles suit traditional entrances. Our wood-look aluminum gates give the look of real wood without the rot, warping or splitting. They are aluminum, not wood, and they need less upkeep than wood.
Does a lighter gate help an automatic opener?
It helps. Mulholland Brand's aluminum gates weigh a third as much as iron, so they put less strain on hinges and gate openers. On automated swing gates we use LiftMaster LA 400 or LA 500 operators, and on automated sliding gates we use BFT operators.
What rust warranty should I ask for?
Ask for the years in writing, what is covered and how to report a problem. Mulholland Brand's warranty is one year for any defect in manufacture or assembly and three years against rust on the product, with problems reported in writing within 7 days.
Book an On-Site Measurement and Written Quote
The next step is simple. One of our design consultants visits your property and measures the opening, grade, swing clearance and drainage. You then receive an itemized written quote for the exact gate. Hold it up against the checklist above, and against any other bid you get.
Mulholland Brand, 7959 Deering Ave, Canoga Park, CA 91304. Our San Diego office is at 6352 Corte Del Abeto, Suite B, Carlsbad, CA 92011. Office hours are Monday to Friday, 8 AM to 5 PM. California contractor license CSLB #1061373.
Call (877) 616-2947 or (800) 562-5770, or request your on-site measurement to start on a driveway gate built to stay right on the Malibu coast.





















